Study of the Test Method of Key Mechanical Parameters of Set Cement in
the Gas Storage Well

doi:10.3863/j.issn.1674–5086.2013.06.016

Abstract

Abstract:

For the purpose of measuring the key mechanical parameters of set cement in the gas storage well：tensile strength
and bonding strength，two new test methods were designed for the two mechanical parameters respectively. Through test
measurement and comparative analysis of 6 sets of typical set cement from the gas storage well，we found that the new methods
have better and more reasonable results. The tensile strength of typical set cement from the gas storage is in the range of
1.5∼3.5 MPa，which is about 7%∼13% of the compressive strength. The mechanical modification to cement has remarkable
effects on the cement′s tensile strength. The longitudinal bonding strength of low density cement is about 0.7∼1.5 MPa，and
the normal density cement is roughly 1.5∼2.5 MPa，which is far enough for supporting casing weight. The cement dangerous
points because of the casing acting are not on the vertical but on the horizontal.

Key words: cementing, gas storage well, tensile strength, bonding strength, test method

Liu Jian1, Guo Xiaoyang2, Li Zaoyuan2. Study of the Test Method of Key Mechanical Parameters of Set Cement in
the Gas Storage Well[J]. 西南石油大学学报(自然科学版), DOI: 10.3863/j.issn.1674–5086.2013.06.016.

0
/ / Recommend

Add to citation manager EndNote|Ris|BibTeX

URL: http://journal15.magtechjournal.com/Jwk_xnzk/EN/10.3863/j.issn.1674–5086.2013.06.016

http://journal15.magtechjournal.com/Jwk_xnzk/EN/Y2013/V35/I6/115

References

[1] Dillenbeck R，Go Boncan V，Rogers M. Testing cement

static tensile behavior under downhole conditions[C]. SPE

97967，2005.

[2] Garnier A，Fraboulet B，Marc J，et al. Characterization

of cement systems to ensure cement sheath integrity[C].

OTC 18754，2007.

[3] James S，Boukhelifa L. Zonal isolation modeling and

measurements-past myths and today’s realities[J]. SPE

Drilling & Completion，2008，23（1）：68–75.

[4] 中国煤炭工业协会. GB/T 2356.10—2010 煤和岩石物

理力学性质测定方法第10 部分：煤和岩石抗拉强度

测定方法[S]. 北京：中国标准出版社，2010.

[5] 戎君明，陆建雯，姚燕，等. GB/T 50081—2002 普通混

凝土力学性能试验方法标准[S]. 北京：中国建筑工业

出版社，2002.

[6] ASTM Committee C09，ASTM C496/C496M—11 Standard

test method for splitting tensile strength of cylindrical

concrete specimens[S]. West Conshohocken：ASTM

International，2011.

[7] 中国石油集团工程技术研究院. GB/T 19139—2003 油

井水泥石试验方法[S]. 北京：中国标准出版社，2003.

[8] 钱觉时，罗晖，王智. 水泥混凝土高强化与强度尺寸效

应[J]. 建筑材料学报，1998，1（2）：134–138.

[9] 钟新联. 统计基础知识[M]. 第3 版. 北京：中国财政经

济出版社，1998：98–129.

[10] 陈勉，金衍，张广清. 石油工程岩石力学[M]. 北京：科

学出版社，2008：29–30.

[11] 姚晓，周兵，李美平，等. 套管试压对水泥环密封性

的影响[J]. 西安石油大学学报：自然科学版，2009，

24（3）：31–34.

[12] Thiercelin M J，Dargaud B，Baret J F，et al. Cement design

based on cement mechanical response[C]. SPE 52890，

1998.

[13] Bosma M，Ravi K，Van Driel W，et al. Design approach

to sealant selection for the life of the well[C]. SPE 56536，

1999.

[14] Shen Z，Beck F. Three-dimensional modeling of casing

and cement sheath behavior in layered，nonhomogeneous

formations[C]. SPE 156496，2012.

[15] Ravi K，Bosma M，Gastebled O. Improve the economics

of oil and gas wells by reducing the risk of cement failure[

C]. SPE 74497，2002.