泥包对破岩效率影响的PDC 单齿切削模型研究

doi:10.11885/j.issn.1674-5086.2013.06.30.02

摘要/Abstract

摘要：

PDC 钻头泥页岩地层钻进易发生泥包，严重影响机械钻速。钻进性能的变化归根结底源于切削齿与地层的
相互作用，但是目前建立的单齿切削模型考虑的因素不全面，并不适用于钻头发生泥包的情况。建立了PDC 钻头分
别发生切削齿泥包和钻头整体泥包时的单齿切削模型，模型全面考虑了围压、切削齿倒角面、切削齿后底面、岩屑破碎
带等因素，通过实例计算、利用前人实验数据验证了模型计算结果的可靠性。最后利用模型量化分析了泥包对破岩效
率的影响规律，结果发现切削齿泥包和钻头泥包均严重影响破岩效率，且后者影响程度更大；切削齿泥包中，围压和
“泥包团”长度对破岩效率影响显著，破岩效率均随两者的增大而减小；钻头泥包中，泥包面积对破岩效率影响显著，
破岩效率随泥包面积的增大而减小。

关键词: PDC 钻头, 泥包, 单齿切削模型, 破岩效率, 泥页岩

Abstract:

Bit balling is a common phenomenon in shale drilling when using PDC bit，which results in seriously reduced ROP.
The change of drill bit performances fundamentally comes from the cutter-rock interaction，but the single cutter-rock interaction
models built by researchers at present didn′t take all the factors into consideration which were not available to the situation of
balling. In this paper，two new PDC single cutter-rock interaction models are built which can be applied to the cases of cutter
balling and global balling separately. The models consider comprehensive factors including confining pressure，forces exerted
on cutter chamfer，the back of the cutter and the build-up edge of cuttings. The results of the models are validated by example
calculation and reference to predecessors′ laboratory data. At last，the effect of bit balling on cutting efficiency is analyeed
quantitatively by using the models，and the results show that both cutter balling and global balling affect the cutting efficiency
seriously，and the latter influences more seriously. In the case of cutter balling，the confining pressure and the length of“cutter
ball”are the two main factors affecting cutting efficiency，which decreases as they increase. In the case of global balling，the
area of balling affects and cutting efficiency greatly，cutting efficiency decreases as the area increases.

Key words: PDC bit, balling, single cutter-rock interaction model, cutting efficiency, shale

中图分类号:

TE21

陈修平*，邹德永. 泥包对破岩效率影响的PDC 单齿切削模型研究[J]. 西南石油大学学报(自然科学版), DOI: 10.11885/j.issn.1674-5086.2013.06.30.02.

Chen Xiuping*, Zou Deyong. Study of the PDC Single-tooth Cutting Model About the Bit Balling on Its#br# Cutting Efficiency[J]. 西南石油大学学报(自然科学版), DOI: 10.11885/j.issn.1674-5086.2013.06.30.02.

0
/ / 推荐

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://journal15.magtechjournal.com/Jwk_xnzk/CN/10.11885/j.issn.1674-5086.2013.06.30.02

http://journal15.magtechjournal.com/Jwk_xnzk/CN/Y2015/V37/I6/158

参考文献

[1] Isbell M R，Scott D E，Freeman M A. Application-specific
bit technology leads to improved performance in unconventional
gas-shale plays[C]//IADC/SPE Drilling Conference
and Exhibition，Society of Petroleum Engineers，
2010.
[2] De Stefano G，Young S. The prevention and cure of
bit balling in water based drilling fluids[C]//Offshore
Mediterranean Conference and Exhibition，Offshore
Mediterranean Conference，2009.
[3] Wells M，Marvel T，Beuershausen C. Bit balling mitigation
in PDC bit design[C]//IADC/SPE Asia Pacific
Drilling Technology Conference and Exhibition，Society
of Petroleum Engineers，2008.
[4] Smith J R. Diagnosis of poor PDC bit performance in
deep shales[D]. Louisiana：Louisiana State University and
Agricultural & Mechanical College，1998.
[5] Ghoshouni M，Richard T. Effect of the back rake angle
and groove geometry in rock cutting[C]//ISRM International
Symposium-5th Asian Rock Mechanics Symposium，
International Society for Rock Mechanics，2008.
[6] Seliami H，Fairhurst C，Deliac E，et al. The role of insitu
rock stresses and mud pressure on the penetration rate
of PDC bits[C]//ISRM International Symposium，International
Society for Rock Mechanics，1989.
[7] Detournay E，Defourny P. A phenomenological model for
the drilling action of drag bits[C]//International Journal of
Rock Mechanics and Mining Sciences & Geomechanics
Abstracts，Pergamon，1992，29（1）：13-23.
[8] Glowka D A. Use of single-cutter data in the analysis of
PDC bit designs：Part 1-development of a PDC cutting
force model[J]. Journal of Petroleum Technology，1989，
41（8）：797 849.
[9] Rahmani R，Smith J R，Taleghani A D. Analytical modeling
of PDC single cutter-rock interaction under confining
pressure[C]//46th US Rock Mechanics/Geomechanics
Symposium，American Rock Mechanics Association，
2012.
[10] Rafatian N，Miska S Z，Ledgerwood L W，et al. Experimental
study of MSE of a single PDC cutter under simulated
pressurized conditions[C]//SPE/IADC Drilling Conference
and Exhibition，Society of Petroleum Engineers，
2009.
[11] Ledgerwood III L W. PFC modeling of rock cutting under
high pressure conditions[C]//1st Canada-US Rock Mechanics
Symposium，American Rock Mechanics Association，
2007.
[12] Zijsling D H. Single cutter testing-a key for PDC bit development[
C]//Offshore Europe，Society of Petroleum Engineers，
1987.
[13] Warren T M，Sinor A. Drag bit performance modeling[
C]//SPE Annual Technical Conference and Exhibition，
Society of Petroleum Engineers，1986.
[14] Rajabov V，Miska S Z，Mortimer L，et al. The effects
of back rake and side rake angles on mechanical specific
energy of single PDC cutters with selected rocks at varying
depth of cuts and confining pressures[C]//IADC/SPE
Drilling Conference and Exhibition，Society of Petroleum
Engineers，2012.
[15] Smith R H，Lund J B，Anderson M，et al. Drilling plastic
formations using highly polished PDC cutters[C]//SPE
Annual Technical Conference and Exhibition，Society of
Petroleum Engineers，1995.