Journal of Southwest Petroleum University(Science & Technology Edition)

STUDY OF UPPER PERMIAN AND LOWER-MIDDLE TRIASSIC CONODONTS FROM SHANG SI,GUANG YUAN-GUAN ZI BA,WANG CHANG,SICHUAN PROVINCE

Jiang Wu Yang Men-Jie

1983, 5(3): 1-16. DOI: 10.3863/j.issn.1000-2634.1983.03.001

Asbtract ( 694 )

PDF (6717KB) ( 598 )

Related Articles | Metrics

The depositional facies and conodonts in the Upper permian and Middle-Lower Triassic Carbonatite in this area are studied in this paper. The emphasis is laid on the genera, species and assemblage of conodonts, and a preliminary division is made of the carbonate facies in different formations. Therefore,the relationship between conodont animals and depositional environments and lithology is described. Besides, the colour alteration of conodonts and its significance in exploring oil and gas is also discussed.

PENETRATION RATE INCREASEMENT WITH IMPROVED BOTTOM-HOLE FLOW FIELD

Drillinq Technoloqy Research secticn

1983, 5(3): 17-31. DOI: 10.3863/j.issn.1000-2634.1983.03.002

Asbtract ( 634 )

PDF (365KB) ( 556 )

Related Articles | Metrics

Analysis of a great many laboratory experiments and some field tests of more than thirty various configurations of nozzles indicates that improved hydraulic clearing system of jet bits and reasonable design of Bottom-hole flow field can increase penetration rate and decrease cost of drilling.

COMPUTER SIMULATION OF BOTTOM HOLE ASSEMBLY

Shi Tai-he

1983, 5(3): 32-44. DOI: 10.3863/j.issn.1000-2634.1983.03.003

Asbtract ( 1291 )

PDF (546KB) ( 387 )

Related Articles | Metrics

The conclusions developed from computer numerical simulation of pa-
eked hole assembly ace of theoretical and practical importance.The results
from simulation can be used as a guide in vertical and directional dril
ing.Fundamental formulae of finite element method in analyzing bottom
hole assembly are given in appendix A.The computer program is v-ritten
in "FORTRAN".All data are input into computer nith0 question and ans-
wer"format.Tabulated data or plot of displacement of bottom hole assem-
bly can be selected at users s will.
It is proved by simulation that the hehavior of bottom hole assernbly
not only depends on bit side force.Both the bit side force and the resul-
taut should be considered in analysis of bottom hole assembly.Three
general types of assembly.holding，building and dropping-aro simu-
lated.Comparison of the results ith field measurements of drilled hole
angles is presented.The computer simulation with the factors of a parti-
cular formaton could be helpful in predicting well trajectary，designing
a proper assembly and determining the Sveight on bit，

HOW TO CALCULATE KICK TOLERANCE

Hao Jun-fang

1983, 5(3): 45-50. DOI: 10.3863/j.issn.1000-2634.1983.03.004

Asbtract ( 859 )

PDF (295KB) ( 718 )

Related Articles | Metrics

The formation position which is easily to lose circulation has been discussed in this paper, and the calculating methods of kick tolerance in three different conditions are presented. Theoretical analysis and calculated data indicate that the well killing kick tolerance K₃is much smaller than K₁ (when there is no kick)and K₂ (when there is a kick in the bottom hole).

MUTUAL ACTION BETWEEN ROCK AND BIT AND WELLBORE DEVIATION

Ma De-kun

1983, 5(3): 51-62. DOI: 10.3863/j.issn.1000-2634.1983.03.005

Asbtract ( 623 )

PDF (676KB) ( 726 )

Related Articles | Metrics

In this report, an overall analysis of wellbore deviation is presented. The theoretical study in side cutting mechanism and side cutting ability of cone bits are described. The facilities for side cutting tests and some test results are introduced

A RESEARCH INTO THE INFLUENCE ON ROCK-BREAKING EFFECT OF THE TEETH STRUCTURE OF THE THREE-CONE BIT

Hou Ji-kang Luo Zhao-feng

1983, 5(3): 63-73. DOI: 10.3863/j.issn.1000-2634.1983.03.006

Asbtract ( 660 )

PDF (971KB) ( 419 )

Related Articles | Metrics

EXPERIMENTAL INVESTIGATION ON INCREASE OF LIFE-TIME OF THE VALVE BODY AND VALVE CUP OF MUD PUMP BY iONIC WELDING

Weiyuan Machine Works;Sichuan Oil and Gas Co. Metallography Teaching And Research Section;South Western Petroleum Institute

1983, 5(3): 74-83. DOI: 10.3863/j.issn.1000-2634.1983.03.007

Asbtract ( 624 )

PDF (1188KB) ( 601 )

Related Articles | Metrics

The valve body and valve cup of mud pump are parts that are easily
to be worn end broken.In order to increase the life-time of these parts,
we studied the technology of increasing the life-time of valve body and
valve cup by ionic welding. On the basis of the results of laboratory and
field experiments the question is discussed on the technology of ionic bead
welding，and wear-resistant alloy for valve body and valve cup，and the
data of the experiments in oil fields are listed .The results of the experi-
menu indicate that the life-time of the valve body and valve cup can be
increased obviously by means of ionic welding.

Table of Content