Loading...

Table of Content

    10 October 2026, Volume 48 Issue 5
    GEOLOGY EXPLORATION
    Sedimentary Facies Characteristics and Evolution of the Middle-Late Permian in the Piedmont Area of Southwestern Tarim Basin
    LUO Qiang, YANG Guang, WANG Jinzhou, SUN Chunyan, LIU Wen, XIA Jinkai
    2026, 48(5):  1-18.  DOI: 10.11885/j.issn.1674-5086.2025.01.14.01
    Asbtract ( 17 )   HTML ( 0)   PDF (9725KB) ( 15 )  
    References | Related Articles | Metrics
    Recent hydrocarbon discoveries in the Yetan-1 and Dewa-1 wells targeting the Middle-Upper Permian clastic rocks in the Kekeya area of the southwestern Tarim foreland highlight the region's exploration potential. However, uncertainties in favorable facies distribution and source-reservoir-seal assemblages constrain further exploration. This study analyzes the sedimentary facies and environments of the Middle-Upper Permian based on observations from 12 outcrop sections, thin section petrography, geochemical data, grain size analysis, heavy mineral assemblages, and zircon U-Pb dating. Results are as follows: 1) Six sedimentary facies are identified in the study area: bay-lagoon, shore-face, braided river delta, alluvial fan, lacustrine, and volcanic overflow facies. 2) The Lower Qipan Formation represents transitional bay-lagoon deposits, shifting to predominantly lacustrine facies in the upper Qipan and Dewa formations, characterized by short transport distances and low sediment maturity, source mainly from the uplifting western Kunlun Mountains. 3) In the Late Permian, the Dewa Formation exhibits clear sedimentary differentiation, with Bamai and most platform-basin regions representing denudation zones, while lacustrine and alluvial fan deposits developed near Sangzhu and Dewa. 4) East of the Xinjiang-Xizang Highway, the Middle-Upper Permian exhibits favorable source-reservoir-seal combinations both laterally and vertically, with thick source rock development and good hydrocarbon generation potential, making the Tiekelike Area a promising exploration target.
    Miocene Sequence Stratigraphic and Sedimentary Characteristics in Taranaki Deepwater Basin, New Zealand
    LIANG Shiqin, WU Wei, WANG Guangxu, GAO Zhixin, ZHOU Yongsheng
    2026, 48(5):  19-31.  DOI: 10.11885/j.issn.1674-5086.2024.08.31.03
    Asbtract ( 14 )   HTML ( 2)   PDF (12372KB) ( 6 )  
    References | Related Articles | Metrics
    Large channel systems, as important deep-sea event deposits, provide important evidence for isochronous stratigraphy identification and comparison due to their abundant erosional and superimposed structures, which can solve the problems of deep-sea sequence stratigraphy division. Based on 3D seismic data and well information, isochronous stratigraphy division and seismic sedimentology analysis were carried out on the Miocene deep-water Taranaki Basin, and the following results were obtained: 1) The Miocene was divided into six third-order sequences, namely SQ1~SQ6, whose sequence boundaries are mainly large-scale erosion surfaces and their corresponding conformable surfaces within deep-water depositional units. Among them, SQ3~SQ6 developed composite channels, which are composite channel series Ⅰ, Ⅱ, Ⅲ and Ⅳ, respectively. 2) Depositional elements such as mass-transport deposits, levees, erosional channel-side deposits, abandoned channels, channel mud deposits, and bottom-current deposits can be identified within the channel system. 3) The deep-sea channel system has obvious evolutionary characteristics. Composite channel series Ⅰ is mainly characterized by incision and lateral migration. The initial geomorphic morphology of the channel was formed after deep incision and widening. Composite channel series Ⅱ is mainly characterized by vertical aggradation, with the channel superimposed upward. Subsequently, channel-fill phase MTD and composite channel series Ⅲ developed. A large number of small, disordered single channels and accompanying mud deposits developed in composite channel series Ⅳ. 4) Tectonic movement, climate change, and sea-level rise and fall jointly control the sediment supply of the basin, thereby affecting the evolution of the composite channel system. The submarine topography, channel, and its own depositional action delicately regulate the channel depositional morphology and evolution process. The results of this study provide a classic case for the interpretation of large-scale deep-sea channel systems. At the same time, they can provide reference value for the exploration and development of this type of oil and gas field.
    Basic Theory Research, Status of Exploration and Development, and Development Direction of Geological Hydrogen
    LI Ning, YANG Zhaobiao, ZHOU Guoxiao, WEI Junqing, ZHANG Baoxin
    2026, 48(5):  32-50.  DOI: 10.11885/j.issn.1674-5086.2025.05.01.01
    Asbtract ( 23 )   HTML ( 0)   PDF (2812KB) ( 15 )  
    References | Related Articles | Metrics
    Geological hydrogen, one of the emerging strategic mineral resources, is expected to take a strategic commanding height of global energy development in the future. The development and utilization of geological hydrogen will effectively solve the problems of energy shortage and environmental pollution. In this paper, the status of exploration and development of geological hydrogen is expounded, the basic geological theory is summarized, and the development direction is eventually clarified. Geological hydrogen resources are of great potential, and many countries have made corresponding plans for its exploration and development. Geological hydrogen is widely distributed and has the potential to form hydrogen reservoirs with high reserves and concentrations. Geological hydrogen has various origins, mainly comprised of inorganic geneses such as serpentinization, radiolysis of water and deep-seated degasification in the earth. And two organic geneses, microbial action and thermal evolution of organic matter, that not only generate hydrogen but also consume hydrogen, could not be neglected. The occurrence characteristics of geological hydrogen vary with various occurrence states, and the transformation will occur between diverse occurrence states. Geological hydrogen is a tremendous "dynamic system", including natural behavior processes such as generation, consumption, migration, accumulation and dissipation. The development direction of geological hydrogen consists of three major modules, namely, basic geological theory, theory and technology of exploration and development, and risk assessment and control of the entire life cycle.
    Prediction of Favorable Reservoirs in Deep-water and Deep-layered Low-permeability Sandstones Based on Grain Size Distribution Patterns
    ZHANG Chong, CHEN Ruxian, YE Qing, ZHOU Wei, LI Hua
    2026, 48(5):  51-66.  DOI: 10.11885/j.issn.1674-5086.2024.08.28.02
    Asbtract ( 12 )   HTML ( 0)   PDF (7972KB) ( 10 )  
    References | Related Articles | Metrics
    Due to the poor quality of deep water seismic data in Baodao B Area in Qiongdongnan Basin, it is difficult to predict favorable lithology. Based on the experimental data of thin section, particle size and minerals of the third member of Lingshui Formation, the grain size distribution characteristics of low permeability sandstone are analyzed. Secondly, the lithology probability sensitive factor curve based on conventional logging data is constructed by using Fisher discriminant analysis method. On this basis, a frequency-division intelligent reservoir inversion method based on lithology probability sensitive factor is proposed to predict favorable lithology distribution. The spatial distribution of favorable lithology is revealed. The results are as follow: 1) The reservoir rocks are characteristic of wide particle size distribution, poor sorting and positive skewness. When the particle size is less than 3.3 ϕ, the permeability is generally greater than 1 mD. According to the grain size classification criteria, the reservoir lithology can be further divided into relatively coarse-grained sandstone (grain size less than 3.3 ϕ), relatively fine-grained sandstone (grain size 3.3~4.0 ϕ) and siltstone-mudstone (grain size greater than 4.0 ϕ). 2) The lithology probability sensitivity factor curve based on FDA discriminating principle is constructed, which can accurately identify the three types of lithology, and the accuracy rate is 27% higher than that of a single logging cross plot. 3) The frequency-division intelligent inversion method of lithology prediction by reconstructing the lithology probability sensitivity factor curve greatly improves the lithology prediction accuracy, and the prediction results show that the relatively coarse lithology is mainly distributed in the northern part of the sedimentary body, which is a potential favorable reservoir distribution area. The research results can provide geological basis for sweet spot evaluation of deep water and low permeability gas reservoirs.
    OIL AND GAS ENGINEERING
    A New Solution of Deliverability Evaluation Formula for Vertically Fractured Gas Wells in Low Permeability Reservoirs
    LIU Qiguo, WANG Jinfan, LIU Cheng, YANG Sihan, LI Ming, HE Shuyao
    2026, 48(5):  67-76.  DOI: 10.11885/j.issn.1674-5086.2024.10.09.02
    Asbtract ( 11 )   HTML ( 0)   PDF (708KB) ( 11 )  
    References | Related Articles | Metrics
    After the gas wells were fractured, the flow of fluid in formations and fractures is no longer a simple linear or radial flow, the flow field became very complicated. Through the analysis of several existing typical capacity forecasting models and the verification of calculation results, we found that many models make assumptions about fluid flow in fractures that are quite different from the actual physical process. The calculated unobstructed flow rate of the gas well has a large error. In this paper, based on the consideration of high-speed non-Darcy flow in fractures, a new fractured gas well productivity calculation model was established in which fluid flows uniformly from the formation to the fracture along the fracture surface, and the inside of the fracture is a variable mass flow. Compared with the calculation results of Saphir software, the new model significantly improves the calculation accuracy. The error is less than 3% on average. This method is simple and easy to use, and is convenient for field application.
    Study on Water Production Mechanism of Tight Gas Reservoirs with High Temperature High Pressure and High Initial Water Saturation
    TANG Ruixue, OU Chenghua, HU Yi, LI Wenhong
    2026, 48(5):  77-87.  DOI: 10.11885/j.issn.1674-5086.2025.03.13.02
    Asbtract ( 12 )   HTML ( 0)   PDF (2744KB) ( 17 )  
    References | Related Articles | Metrics
    A large number of tight gas resources with of high temperature, high pressure and high initial water saturation are found in the east of China, where over 20 horizontal wells exhibit severe water production, below-expected gas output and limited post-fracturing stimulation during the past decade, accurate assessment of reservoir developability remains challenging. Based on the capillary pressure curve and the initial water saturation, a parallel capillary model describing respective seepage of gas and water phase in microscopic pore-throat structure is set up. Combined with the relative permeability curve of gas and water under high-temperature and high-pressure conditions, we make a theoretical probe into the production mechanism of movable water under steep driving pressure gradient in such tight gas reservoirs. Moreover, an instance of condensate gas well indicates that this method has more accurate prediction, and can be applied to guide the well position design in such tight gas reservoirs, which has a good promotion and application value.
    A Research on Formation Mechanism of Complex Fractures and Stimulation Parameter Limits for Tight Gas in Northeastern Sichuan
    GENG Anran, DUAN Yonggang, WANG Hongjian, WEI Mingqiang, ZENG Hao
    2026, 48(5):  88-103.  DOI: 10.11885/j.issn.1674-5086.2026.03.09.01
    Asbtract ( 15 )   HTML ( 0)   PDF (76147KB) ( 10 )  
    References | Related Articles | Metrics
    The Xujiahe Formation in the Sichuan Basin contains abundant tight sandstone gas resources. Matrix-type reservoirs with porosity of 3%~4%, or slightly fractured matrix-type reservoirs, account for a relatively high proportion and form the basis for stable gas-field production. To achieve a breakthrough in the productivity of such reservoirs, outcrop sandstone samples from matrix-type and micro-fracture-developed matrix-type reservoirs in the Xujiahe Formation and Qianfoya Formation of the Puguang Gas Field were selected. True triaxial fracturing experiments and fracture propagation simulations were conducted to reveal the formation mechanism of complex fractures, clarify the effects of pumping rate, fluid viscosity, and micro-fractures on reservoir stimulation, and propose and test the limits of fracturing treatment parameters. The results show that: 1) reservoirs with developed micro-fractures are more likely to form complex fractures during fracturing; 2) when the in-situ stress difference coefficient is 0.3, complex fractures are formed more effectively; 3) for reservoirs with developed micro-fractures, better fracturing performance is achieved when the pumping rate is ≥13.50 m3/min and the fluid viscosity is 5~10 mPa·s; 4) for reservoirs without developed micro-fractures, relatively better fracturing performance is achieved when the pumping rate is ≥20.25 m3/min and the fluid viscosity is 5 mPa·s; 5) if micro-fractures are developed near the wellbore, high-viscosity fluids used to create long fractures can also form complex fractures. And after field application, the daily gas production of a single well increased by approximately twofold. These results provide key support for reservoir stimulation in this area and offer a reference for the stimulation of similar reservoirs.
    A Study on Evolution of Shale Permeability Considering the Dual Effects of Poroelasticity and Gas Dynamics
    CHEN Yufei, CHEN Weimeng, ZHANG Qiangui, FAN Xiangyu, JIANG Changbao
    2026, 48(5):  104-113.  DOI: 10.11885/j.issn.1674-5086.2024.09.19.01
    Asbtract ( 10 )   HTML ( 0)   PDF (1272KB) ( 7 )  
    References | Related Articles | Metrics
    In view of the fact that the shale permeability is affected by both poroelasticity effect and gas dynamics effect during gas production, this study conducted shale permeability experiments under constant effective stress (CES) and constant confining pressure (CCP) conditions using Longmaxi shale samples drilled in the Sichuan Basin. The results show that under CES condition, the apparent permeability of shale increases with decreasing pore pressure, and this effect is particularly pronounced when pore pressure is less than almost 6 MPa; while under CCP condition, the apparent permeability of shale first decreases and then increases with decreasing pore pressure, showing a “V”-shaped dual evolution law. Based on this, we derived a shale permeability model considering the dual effects of poroelasticity and gas dynamics, and it agrees well with both CES and CCP experimental data. During the full-life-cycle developments of shale gas, the gas flow behavior in shale reservoirs will transform from poroelasticity-to gas dynamics-dominated to enhance the apparent permeability. Additionally, when the contribution of gas dynamics effect to the shale permeability evolution is close to 25%, a permeability rebound will occur.
    Prediction Model for Flow-cease Timing of Flowing Wells in Shunbei Oilfield
    REN Xianghai, DING Baodong, PENG Zhenhua, DING Wen
    2026, 48(5):  114-123.  DOI: 10.11885/j.issn.1674-5086.2025.04.17.32
    Asbtract ( 14 )   HTML ( 0)   PDF (5268KB) ( 6 )  
    References | Related Articles | Metrics
    Shunbei oilfield produces in depletion drive, and there exist large differences in production and gas-liquid ratio, and complex porous flow. As production progresses, formation pressure decreases and more wells are facing failure to flow. Accurate prediction of formation pressure and production when the wells cease to flow is crucial for early intervention and design of artificial lift. Therefore, this paper proposes a prediction method based on node analysis method for gusher wells in Shunbei oilfield, taking the production and pressure at the only intersection point of reservoir inflow curve and wellbore outflow curve as production at flow cease and bottomhole flowing pressure. The key is to accurately the future formation production and wellbore pressure drop calculation. Firstly, based on the high pressure PVT test and the Vasquez-Beggs model, a modified model for physical property of crude oil in Shunbei Oilfield was established. Then, coupling the model with the commonly used pressure drop models in engineering, the Mukherjee-Brill model was optimized to calculate the wellbore pressure drop in Shunbei Oilfield. Then, based on the characteristics of single-phase and two-phase porous flow, the model of inflow performance relationship in future formation pressure in Shunbei oilfield was established. Finally, the model was verified based on the wells which cease flowing in Shunbei Oilfield, and the results were highly consistent with these wells, which verifies the reliability of the model. Furthermore, the effect of gas-liquid ratio, tubing pressure and liquid production index on the formation pressure at flow cease were analyzed. This method can provide technical reference for the flow-cease time prediction of similar reservoirs.
    Influence of Horizontal Well Structure on Gas-liquid Sand-carrying Flow in the Whole Wellbore
    WAN Huaxu, ZHANG Yuhao, ZHAO Kunpeng, BAI Bofeng
    2026, 48(5):  124-134.  DOI: 10.11885/j.issn.1674-5086.2025.04.07.01
    Asbtract ( 13 )   HTML ( 0)   PDF (6226KB) ( 7 )  
    References | Related Articles | Metrics
    Sand production after large-volume fracturing in shale gas horizontal wells can easily cause wellbore sand plugging, making the study of gas-liquid-sand multiphase flow characteristics essential for sand control. Based on an actual gas well, a full wellbore configuration incorporating the perforated interval, horizontal section, deviated section (comprising build-up, hold, and drop-off segments), and vertical section was constructed, and the gas-liquid-sand three-phase flow was numerically investigated using the Eulerian multiphase model, focusing on the influence of wellbore geometry. The results show that sand transport is inherently driven by gas carrying liquid and liquid carrying sand. Intermittent sand dunes or sand beds form in the horizontal and deviated sections, and in the radial direction, high-velocity sand transport, movement of sand grains on the bed surface, a moving sand bed, and a stationary sand bed appear successively. In the vertical section, the sand distribution becomes uniform and backflow occurs. Sand accumulation in the deviated section originates from the stationary sand bed induced by wall shear and sand backflow from the vertical section; it exhibits the highest sand holdup, the thickest stationary sand bed, and the lowest sand transport velocity, making it the most severe sand deposition region in the wellbore. Longer horizontal and deviated sections make sand transport more difficult, whereas a smaller tubing string enhances the flow velocity and favors sand transport. The build-up section is the most likely location for sand plugging, and the risk increases with higher dogleg severity. This study provides theoretical support for drilling, sand control and plug removal, and enhanced recovery in shale gas horizontal wells.
    Connotations of Displacement Pressure and Breakthrough Pressure and Their Application in Caprock Sealing Evaluation
    JIANG Zhibin, YU Beibei, CHEN Wei, WANG Wenquan, HUANG Nan, TONG Zhongzheng
    2026, 48(5):  135-145.  DOI: 10.11885/j.issn.1674-5086.2025.05.29.01
    Asbtract ( 15 )   HTML ( 0)   PDF (1224KB) ( 10 )  
    References | Related Articles | Metrics
    To address the confusion between displacement pressure and breakthrough pressure in caprock evaluation for gas storage, this study establishes a three-stage physical model of gas migration and clarifies the essential differences between the two parameters: displacement pressure characterizes the critical capillary resistance for initial gas invasion into pore throats, while breakthrough pressure corresponds to the failure threshold at which gas forms a continuous percolation path. The conventional breakthrough pressure method tends to overestimate caprock sealing capacity due to limited core size and insufficient constant-pressure duration. Therefore, a new displacement pressure testing method is proposed, which improves the testing precision of displacement pressure by extending core length and constant-pressure duration and adopting meniscus movement as the criterion. Application in Block L of North China Basin demonstrates that the displacement pressure measured by this method directly reflects the critical capacity of caprock to resist initial gas invasion, providing a quantitative basis for gas storage operating pressure design; in contrast, the values measured by the breakthrough pressure method are much higher than displacement pressure, making it difficult to reflect the lower risk limit of long-term caprock sealing. Furthermore, a four-level classification standard is established based on displacement pressure, and a systematic evaluation framework of "physical mechanism-testing method-classification application" is constructed, providing theoretical support and practical pathways for caprock evaluation of aquifer gas storage.
    The Coupled Aggregation Characteristics of Micrometer-scale Sand and Hydrate in Pipelines
    YU Cheng, HAN Chuanjun, DU Mingjun, XIE Rui, LI Honglin
    2026, 48(5):  146-158.  DOI: 10.11885/j.issn.1674-5086.2024.08.14.01
    Asbtract ( 9 )   HTML ( 0)   PDF (4360KB) ( 4 )  
    References | Related Articles | Metrics
    In the gas hydrate production operations, the sand produced during hydrate extraction and the aggravated secondary formation of hydrate pose great risks of pipeline blockage, which presents enormous challenges to ensuring the safe flow in the production pipelines. Therefore, based on the population balance theory, considering the collision, agglomeration, and breakage behaviors of micrometer-scale sand particles and hydrates during the flow process, a particle aggregation kinetic model was established. The CFD software was used to solve the coupled multiphase flow model, turbulence model, and particle aggregation kinetic model, simulating the coupled agglomeration process of sand particles and hydrates in the pipe, and analyzing the influence laws of hydrate and sand particle volume fractions and particle sizes on the process. The study found that the coupled agglomeration process of micrometer-scale sand particles and hydrates can be divided into two stages: rapid growth and dynamic equilibrium. The variation laws of the solid particle agglomeration process under different hydrate volume fractions, particle sizes, and sand particle volume fractions are consistent, but when the sand particle diameter is 10 μm, the rapid growth stage is significantly prolonged. As the volume fraction and particle size of hydrates increase, the average particle size of hydrates increases while the average particle size of sand decreases. With the increase in the volume fraction of sand, the average particle sizes of both hydrates and sand, as well as the slurry viscosity, all increase, but the rate of increase gradually slows down.
    PETROLEUM MACHINERY AND OILFIELD CHEMISTRY
    A Study on the Impact Performance and Dynamic Characteristics of Drilling Jars in Ultra-deep Wells
    WANG Zhe, WANG Chunsheng, FENG Shaobo, LIAN Zhanghua, LI Ning
    2026, 48(5):  159-168.  DOI: 10.11885/j.issn.1674-5086.2024.11.15.01
    Asbtract ( 11 )   HTML ( 0)   PDF (1950KB) ( 13 )  
    References | Related Articles | Metrics
    To address the significant differences in the impact effectiveness of drilling jars and the unclear dynamic response behavior of the drill string during the stuck pipe release process in the ultra-deep wells, a systematic evaluation and analysis of the impact performance of drilling jars is urgently needed. Therefore, based on the working principle of the drilling jar, this study employs the finite element explicit dynamics method to establish a transient evaluation model for the impact effectiveness of drilling jars, considering the actual three-dimensional wellbore trajectory. Taking a specific ultra-deep well in the Tarim Basin as an example, the study clarifies the instantaneous impact load and the dynamic response characteristics of the wellbore drill string during the up and down jarring operations. The results indicate that the maximum instantaneous impact load of the jar is 1 999 kN during the up-jarring process and 1 442 kN during the down-jarring operations. Due to the effects of friction and damping, the amplitude of the shock waves generated by the jar gradually decreases as they propagate along the drill string, while the range of fluctuation gradually increases. Additionally, during the up and down jarring operations, the release forces at the stuck points are 2 081 kN and 1 936 kN, respectively, which are 2.60 and 3.87 times the initial jarring forces. These results can provide significant guidance for the efficient and safe execution of stuck pipe release operations in actual deep and ultra-deep wells.
    Research and Application of Measurement and Classification Methods for Rock Abrasiveness in Drilling Engineering
    YANG Yingxin, FENG Hangji, CHEN Lian, WANG Haige, LI Bin
    2026, 48(5):  169-178.  DOI: 10.11885/j.issn.1674-5086.2024.03.11.02
    Asbtract ( 11 )   HTML ( 0)   PDF (2236KB) ( 12 )  
    References | Related Articles | Metrics
    The scientific evaluation of the strength of rock abrasiveness is of great significance for drilling engineering, geology, mining and other drilling and excavation engineering practices. So far, there has been no widely accepted and applied classification standard or specification for rock abrasiveness measurement in the field of drilling and excavation rock breaking engineering. The paper compares existing methods for determining rock abrasiveness, analyzes the requirements for rock abrasiveness testing methods in drilling engineering, and identifies issues that need to be addressed in the development of measurement standards, and introduces the research and application results of using the principle of steel pipe drilling and grinding to determine and classify rock abrasiveness. The proposed steel pipe drilling and grinding method has a simple and feasible testing principle. It is very suitable as a standardized test method for determining rock abrasiveness in drilling engineering. The rock abrasiveness classification method based on the wear of drilling and grinding pipes can meet the technical requirements of different types in drilling engineering applications. The proposed rock abrasiveness measurement and classification technology has been proven to be effective in practical applications. It is recommended that this technology be used as a direct basis for formulating rock abrasiveness measurement and classification standards in the field of drilling engineering. This technology can also be applied to the evaluation of rock abrasiveness in mining, non-excavation, and underground space engineering projects. And this technology can serve as a reference for the design, manufacturing, selection, and use of related products for rock breaking tools.