喷射器气体动力函数法的真实气体修正

doi:10.11885/j.issn.1674-5086.2017.09.28.01

摘要/Abstract

摘要： 索科洛夫提出的气体动力函数法是喷射器经典的设计方法，但是其基于理想气体的假设使得该方法应用于高压的真实气体时误差较大。运用气体热力学方法，从焓和定压比热容的定义入手，引入真实气体等熵温度绝热指数和等熵容积绝热指数，结合能量方程，推导出基于真实气体的气体动力学函数理论式。在此基础上，依据动量守恒和质量守恒定律，推导出了基于真实气体的气体喷射器与气力输送喷射器的基本方程。与索科洛夫设计方法进行了对比，结果表明，低压工况下，基于真实气体的修正方法与索科洛夫设计方法计算结果吻合，说明修正的设计方法覆盖了索科洛夫设计方法；但在高压工况下，两种设计方法的结果差异明显。基于真实气体的修正弥补了索科洛夫设计方法的局限，可适用于全压范围的喷射器设计。

关键词: 喷射器, 设计方法, 真实气体, 热力学, 气体动力学函数

Abstract: The gas dynamic function method proposed by Sokolov is a classical method for designing injectors. However, its assumptions based on ideal gases make it error-prone when it is applied to real gases under high pressures. The gas thermodynamic method was used in this study. The real gas adiabatic indices at isentropic temperatures and isentropic volumes were introduced from the definitions of enthalpy and constant-pressure specific heat. Combined with the energy equations, the theoretical formula of the real gas dynamic function was derived. The basic equations of gas injectors and pneumatic delivery injectors based on real gases were then derived according to the laws of momentum conservation and mass conservation. A comparison with Sokolov's design method showed that, under the low-pressure working condition, the computational results obtained using the revised method based on real gases were consistent with results obtained with Sokolov's design method, indicating that the revised design method covered Sokolov's design method. However, under the high-pressure working condition, the results for these two design methods were significantly different. The real gas correction compensated for the limitations of Sokolov's design method and can be applied to injector design for the entire pressure range.

Key words: ejector, design method, real gas, thermodynamics, gas dynamics function

中图分类号:

TE933
TH48

周三平, 谷平. 喷射器气体动力函数法的真实气体修正[J]. 西南石油大学学报(自然科学版), 2018, 40(5): 170-180.

ZHOU Sanping, GU Ping. Real Gas Correction on Gas Dynamics Function Method About Ejector[J]. 西南石油大学学报(自然科学版), 2018, 40(5): 170-180.

0
/ / 推荐

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://journal15.magtechjournal.com/Jwk_xnzk/CN/10.11885/j.issn.1674-5086.2017.09.28.01

http://journal15.magtechjournal.com/Jwk_xnzk/CN/Y2018/V40/I5/170

参考文献

[1] DEBERNE N, LEONE J F, DUQUE A, et al. A model for calculation of steam injector performance[J]. International Journal of Multiphase Flow, 1999, 25(5):841-855. doi:10.1016/S03019322(98)000718
[2] 贺遵义. 气体射流泵举升工艺及应用[J]. 钻采工艺, 2000, 23(3):47-50. doi:10.3969/j.issn.1006--768X.2000.03.011 HE Zunyi. Lift technology of gas jet pump and it's application[J]. Drilling & Production Technology, 2000, 23(3):47-50. doi:10.3969/j.issn.1006-768X.2000.03.011
[3] 陆宏圻. 喷射技术理论及应用[M]. 武汉:武汉大学出版, 2004. LU Hongqi. Theories and application of ejector technology[M]. Wuhan:Wuhan University Press, 2004.
[4] 姚志良,李明忠,张树华,等. 蒸汽喷射泵举升稠油参数设计[J]. 中国石油大学学报(自然科学版), 2008, 32(6):96-100. doi:10.3321/j.issn:1673-5005.-2008.06.020 YAO Zhiliang, LI Mingzhong, ZHANG Shuhua, et al. Parameter design for lifting heavy oil by steam jet pump[J]. Journal of China University of Petroleum (Science & Technology Edition), 2008, 32(6):96-100. doi:10.3321/j.-issn:1673-5005.2008.06.020
[5] 陆宏圻,陆东宏. 喷射技术研究及其发展空间展望[J]. 前沿科学,2011,5(3):32-39. doi:10.3969/j.issn.1673-8128.2011.03.006 LU Hongqi, LU Donghong. Strive to explore the scientific and technological knowledge, broaden the injection technology development[J]. Frontier Science, 2011, 5(3):32-39. doi:10.3969/j.issn.1673-8128.2011.03.006
[6] 刘效洲. 低压引射式煤粉喷射器的设计[J]. 流体机械,2012,40(9):39-42. doi:10.3969/j.issn.1005-0329.-2012.09.009 LIU Xiaozhou. Innovative design of low-pressure jetcoal powder ejector[J]. Fluid Machinery, 2012, 40(9):39-42. doi:10.3969/j.issn.1005-0329.2012.09.009
[7] 刘双全,汪雄雄,樊莲莲,等. 靖边气田喷射器和压缩机组合增压新工艺[J]. 天然气工业, 2013, 33(5):96-99. doi:10.3787/j.issn.1000-0976.2013.05.018 LIU Shuangquan, WANG Xiongxiong, FAN Lianlian, et al. A new technique of supercharging by ejectors and compressors in the Jingbian Gas Field, Ordos Basin[J]. Natural Gas Industry, 2013, 33(5):96-99. doi:10.3787/j.issn.-1000-0976.2013.05.018
[8] 戴征书,陈光明,张华,等. 喷射器极限工况特性实验研究[J]. 制冷学报, 2017, 38(5):114-118. doi:10.3969/j.issn.0253-4339.2017.05.114 DAI Zhengshu, CHEN Guangming, ZHANG Hua, et al. Experimental study on ejector performance underlimiting operating condition[J]. Journal of Refrigeration, 2017, 38(5):114-118. doi:10.3969/j.issn.0253-4339.-2017.05.114
[9] EL-DESSOUKY H, ETTOUNEY H, ALATIQI I, et al. Evaluation of steam jet ejectors[J]. Chemical Engineering & Processing Process Intensification, 2002, 41(6):551-561. doi:10.1016/S0255-2701(01)00176-3
[10] HOGGARTH M L. The design and performance of highpressure injectors as gas jet boosters[J]. Proceedings of the Institution of Mechanical Engineers, 1970, 185:755-766. doi:10.1243/PIME_PROC_19-70_185_089_02
[11] MUNDAY J T, BAGSTER D F. A new ejector theory applied to steam jet refrigeration[J]. Industrial & Engineering Chemistry Process Design and Development, 1977, 16(4):442-449. doi:10.1021/i260064a003
[12] DUTTON J, MIKKELSEN C, ADDY A. A theoretical and experimental investigation of the constant area, supersonic-supersonic ejector[J]. AIAA Journal, 1982, 20(10):1392-1400. doi:10.2514/3.51199
[13] SUN D W, EAMES I W. Recent developments in the design theories and applications of ejectors[J]. Journal of the Institute of Energy, 1995, 68:65-79.
[14] ALY N H, KARAMELDIN A, SHAMLOUL M M. Modelling and simulation of steam jet ejectors[J]. Desalination, 1999, 123(1):1-8. doi:10.1016/S0011-9164(99)-00053-3
[15] HUANG B J, CHANG J M. Empirical correlation for ejector design[J]. International Journal of Refrigeration, 1999, 22(5):379-388. doi:10.1016/S0140-7007(9-9)00002-X
[16] [苏]E Я索科洛夫H M. 喷射器[M]. 津格尔,黄秋云, 译. 北京:科学出版社, 1977.
[17] 韩惠霖. 喷射理论及其应用[M]. 杭州:浙江大学出版社, 1990. HAN Huilin. Jet theories and its applications[M]. Hangzhou:Zhejiang University Press, 1990.
[18] 王权,向雄彪. 蒸汽喷射压缩器喷射系数计算方法研究[J]. 太阳能学报, 1997(3):314-321. WANG Quan, XIANG Xiongbiao. A study of method for calculating jet coefficient of steam jet compressor[J]. Acta Energiae Solaris Sinica, 1997(3):314-321.
[19] 刘中常,李维. 亚临界气体喷射器的设计计算[J]. 南京工业大学学报(自然科学版), 2006, 28(5):84-88. doi:10.3969/j.issn.1671-7627.2006.05.018 LIU Zhongchang, LI Wei. Design and calculation of subcritical gas ejector[J]. Journal of Nanjing University of Technology (Natural Science Edition), 2006, 28(5):84-88. doi:10.3969/j.issn.1671-7627.2006.05.018
[20] 沈胜强,张琨. 新型可调式喷射器性能的计算与分析[J]. 热科学与技术, 2007, 6(3):230-234. doi:10.-3969/j.issn.1671-8097.2007.03.009 SHEN Shengqiang, ZHANG Kun. Study and calculation of performance of adjustable ejector[J]. Journal of Thermal Science and Technology, 2007, 6(3):230-234. doi:10.3969/j.issn.1671-8097.2007.03.009
[21] 吴伟烽,冯全科,向清江,等. 气-液喷射器内两相流流型分析[J]. 核动力工程, 2007, 28(6):34-38. doi:10.3969/j.issn.0258-0926.2007.06.009 WU Weifeng, FENG Quanke, XIANG Qingjiang, et al. Analysis of inner flow patterns in gas-liquid ejectors[J]. Nuclear Power Engineering, 2007, 28(6):34-38. doi:10.3969/j.issn.0258-0926.2007.06.009
[22] 李勇明,江有适,高瑞民,等. 天然气喷射压力计算方法与应用分析[J]. 延安大学学报(自然科学版), 2011, 30(4):31-34. doi:10.3969/j.issn.1004-602X.2011.04.011 LI Yongming, JIANG Youshi, GAO Ruimin, et al. The calculation of gas ejection pressure and application analysis[J]. Journal of Yanan University (Natural Science Edition), 2011, 30(4):31-34. doi:10.3969/j.issn.1004-602X.2011.04.011
[23] ROGDAKIS E D, ALEXIS G K. Design and parametric investigation of an ejector in an air-conditioning system[J]. Applied Thermal Engineering, 2000, 20(2):213-226. doi:10.1016/S1359-4311(99)00013-7
[24] OUZZANE M, AIDOUN Z. Model development andnumerical procedure for detailed ejector analysis anddesign[J]. Applied Thermal Engineering, 2003, 23(1-8):2337-2351. doi:10.1016/S1359-4311(03)002084
[25] VALLE J G, JABARDO J M, RUIZ F C. A one dimensional model for the determination of an ejector entrainment ratio[J]. International Journal of Refrigeration, 2012, 35(4):772-784. doi:10.1016/j.ijrefrig.2-011.11.020
[26] 王菲,吕恒林,冯伟,等. 压缩/喷射制冷循环中两相喷射器性能[J]. 化工学报, 2012, 63(10):3094-3100. doi:10.3969/j.issn.0438-1157.2012.10.013 WANG Fei, LÜ Henglin, FENG Wei, et al. Performance of two-phase ejector in compression/ejection refrigeration cycle[J]. CIESC Journal, 2012, 63(10):3094-3100. doi:10.3969/j.issn.0438-1157.2012.10.013
[27] 陈洪杰,卢苇,庄光亮. 基于实际气体的圆柱形混合室喷射器设计及优化方法[J]. 化工学报, 2015, 66(10):3881-3887. doi:10.11949/j.issn.0438-1157.20150150 CHEN Hongjie, LU Wei, ZHUANG Guangliang. Method for design and optimization of cylindrical mixing chamber ejector based on real gas properties[J]. CIESC Journal, 2015, 66(10):3881-3887. doi:10.1-1949/j.issn.0438-1157.20150150
[28] SHI Chaoyin, CHEN Huiqiang, CHEN Weixiong, et al. 1D model to predict ejector performance at critical and subcritical operation in the refrigeration system[J]. Energy Procedia, 2015, 75:1477-1483. doi:10.1016/j.egypro.-2015.07.271
[29] 戴征书,陈光明,张华. 内部不可逆损失对喷射器性能影响理论分析[J]. 化工学报,2016,67(s2):78-86. doi:10.11949/j.issn.0438-1157.20161379 DAI Zhengshu, CHEN Guangming, ZHANG Hua. Theoretical analysis on impact of irreversibility on ejector performance[J]. CIESC Journal, 2016, 67(s2):78-86. doi:10.11949/j.issn.0438-1157.20161379
[30] 高建安. 推证热力学函数偏微商的简捷方法[J]. 江西理工大学学报, 1992(4):353-361. doi:10.13265/j.-cnki.jxlgdxxb.1992.04.013 GAO Jian'an. A simplified method of deducing partial derivatives of thermodynamic function[J]. Journal of Jiangxi University of Science and technology, 1992(4):353-361. doi:10.13265/j.cnki.jxlgdxxb.1992.04.013
[31] 苏长荪. 高等工程热力学[M]. 北京:高等教育出版社, 1987. SU Changsun. Advanced engineering thermodynamics[M]. Beijing:Higher Education Press, 1987.
[32] 刘晖. 实际气体温度绝热指数和容积绝热指数的计算[J]. 石油化工高等学校学报, 2000, 13(4):42-45. doi:10.3969/j.issn.1006-396X.2000.04.009 LIU Hui. Calculation of the isentropic temperature change exponent and isentropic volume change exponent of real gase[J]. Journal of Petrochemical Universities, 2000, 13(4):42-45. doi:10.3969/j.issn.10-06-396X.2000.04.-009