深层超稠油油藏蒸汽吞吐后转汽驱实验研究

doi:10.11885/j.issn.16745086.2020.03.24.02

摘要/Abstract

摘要： 辽河油田曙一区深层超稠油油藏经历多年蒸汽吞吐开发，取得了一定的开发效果，但进入吞吐开发中后期，面临周期产油量低、油汽比低及稳产难度逐年增大等问题，蒸汽吞吐后接替技术的研究已迫在眉睫。在室内利用高温高压比例物理模拟装置，针对蒸汽吞吐后转蒸汽驱的影响因素、调控策略和生产特征开展了实验研究。结果表明，蒸汽吞吐阶段形成的温场对后续蒸汽驱开发有较大影响。蒸汽吞吐转汽驱的前提条件，一是注采井间油层热连通温度要达到原油转驱温度以上，二是吞吐阶段培育的蒸汽腔体积要足够大，横向波及注采井距1/3左右为宜。注采井段调整是改善汽驱效果的重要影响因素。对于层内无稳定分布的夹层情况，蒸汽吞吐及蒸汽驱阶段注汽井采用下1/2井段注汽，能够有效抑制汽体超覆，提高采出程度。当蒸汽驱达到剥蚀生产阶段后，将生产井由全井段调整为下1/2井段生产，能够在一定程度上扩大波及体积，提高采出程度；超稠油蒸汽驱生产特征以剥蚀作用为主，驱替作用为辅。研究结果为深层超稠油油藏蒸汽吞吐后转汽驱开发方案优化设计及矿场试验提供理论依据。

关键词: 超稠油油藏, 蒸汽驱, 转驱温度, 驱替特征, 调控策略, 实验研究

Abstract: The deep super heavy oil reservoir in Shu1 area of Liaohe Oilfield has been developed by steam stimulation for many years, and has achieved certain development results. However, after entering into mid-and late stage of huff and puff, it is faced with the problems of low cycle oil production, low oil steam ratio, increasing difficulty of stable production, etc., so it is urgent to study the replacement technology after steam stimulation. In this paper, the influence factors, control strategies and production characteristics of steam flooding after huff and puff are studied by using the high temperature and high pressure proportional physical simulation device. The results show that the characteristics of temperature field formed in the steam huff and puff stage have great influence on the subsequent steam flooding development. The preconditions for steam stimulation to steam flooding are:first, the temperature of thermal connection between injection and production wells should be above the critical temperature of crude oil; second, the volume of steam cavity cultivated in the stimulation stage should be large enough, and the lateral sweep should be about one third of the injection production well spacing; the adjustment of injection production well section is an important factor to improve the effect of steam flooding. For the case that there is no stable interlayer in the layer, the steam injection in the lower 1/2 well section can effectively restrain the steam body overlap and improve the recovery degree. When the steam flooding reaches the stage of denudation production, adjusting the production well from the whole well section to the lower 1/2 well section can enlarge the wave and volume to a certain extent and improve the recovery degree; the production characteristics of super heavy oil steam drive are mainly denudation, supplemented by displacement. The results provide a theoretical basis for the optimization design of the development plan and field test after steam stimulation in deep super heavy oil reservoir.

Key words: super heavy oil reservoir, steam flooding, transfer temperature, displacement characteristics, control strategy, experimental research

中图分类号:

TE357

赵庆辉, 张鸿, 杨兴超, 程海清, 潘攀. 深层超稠油油藏蒸汽吞吐后转汽驱实验研究[J]. 西南石油大学学报(自然科学版), 2021, 43(3): 146-154.

ZHAO Qinghui, ZHANG Hong, YANG Xingchao, CHENG Haiqing, PAN Pan. An Experimental Study on Steam Flooding After Huff and Puff in Deep Super Heavy Oil Reservoir[J]. Journal of Southwest Petroleum University(Science & Technology Edition), 2021, 43(3): 146-154.

0
/ / 推荐

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://journal15.magtechjournal.com/Jwk_xnzk/CN/10.11885/j.issn.16745086.2020.03.24.02

http://journal15.magtechjournal.com/Jwk_xnzk/CN/Y2021/V43/I3/146

参考文献

[1] 刘福余. 曙一区超稠油开采特征及开发对策[J]. 特种油气藏,2002,9(6):1-5. doi:10.3969/j.issn.1006-6535.2002.06.001 LIU Fuyu. Recovery feature and development game of super heavy oil in Shu 1 Area[J]. Special Oil and Gas Reservoirs, 2002, 9(6):1-5. doi:10.3969/j.issn.10066535.2002.06.001
[2] 孙新革,赵长虹,熊伟,等. 风城浅层超稠油蒸汽吞吐后期提高采收率技术[J]. 特种油气藏,2018,25(3):72-76,81. doi:10.3969/j.issn.1006-6535.2018.03.014 SUN Xinge, ZHAO Changhong, XIONG Wei, et al. Enhanced oil recovery in the late stage of shallow super-heavy oil reservoir with steam huff-puff in Fengcheng Oilfield[J]. Special Oil & Gas Reservoirs, 2018, 25(3):72-76, 81.10.3969/j.issn.1006-6535.2018.03.014
[3] 王学忠. 多轮次蒸汽吞吐井开发接替技术研究[J]. 当代石油石化,2019,27(6):30-34. doi:10.3969/j.issn.1009-6809.2019.06.006 WANG Xuezhong. Research on development replacement technology of multi-cycle steam huff and puff wells[J]. Petroleum & Petrochemical Today, 2019, 27(6):30-34. doi:10.3969/j.issn.1009-6809.2019.06.006
[4] 张义堂,陈亚平,刘尚奇,等. 热力采油提高采收率技术[M]. 北京:石油工业出版社,2006:20-24. ZHANG Yitang, CHEN Yaping, LIU Shangqi, et al. EOR technology by thermal recovery[M]. Beijing:Petroleum Industry Press, 2006:20-24.
[5] 赵庆辉,冷光耀,彭旭. 注空气改善稠油油藏蒸汽吞吐开采效果的实验研究[J]. 西安石油大学学报(自然科学版),2018,33(6):55-59. doi:10.3969/j.issn.1673-064X.2018.06.008 ZHAO Qinghui, LENG Guangyao, PENG Xu. Experimental study on improving effect of steam stimulation in heavy oil reservoir by air injection[J]. Journal of Xi'an Shiyou University (Natural Science Edition), 2018, 33(6):55-59. doi:10.3969/j.issn.1673-064X.2018.06.008
[6] 刘文章. 特稠油、超稠油油藏热采开发模式综述[J]. 特种油气藏,1998,5(3):1-7,11. LIU Wenzhang. An overview on thermal development mode of super viscous crude oil and extra viscous crude oil reservoir[J]. Special Oil & Gas Reservoirs, 1998, 5(3):1-7, 11.
[7] 王胜,曲岩涛,韩春萍. 稠油油藏蒸汽吞吐后转蒸汽驱驱油效率影响因素——以孤岛油田中二北稠油油藏为例[J]. 油气地质与采收率,2011,18(1):48-50. doi:10.3969/j.issn.1009-9603.2011.01.014 WANG Sheng, QU Yantao, HAN Chunping. Influencing factors study on oil displacement efficiency after steam simulation in heavy oil reservoir[J]. Petroleum Geology and Recovery Efficiency, 2011, 18(1):48-50. doi:10.3969/j.issn.1009-9603.2011.01.014
[8] 张方礼,张丽萍,鲍君刚,等. 蒸汽辅助重力泄油技术在超稠油开发中的应用[J]. 特种油气藏,2007,14(2):70-72. doi:10.3969/j.issn.1006-6535.2007.02.017 ZHANG Fangli, ZHANG Liping, BAO Jungang, et al. Application of SAGD in ultra heavy oil development[J]. Special Oil and Gas Reservoirs, 2007, 14(2):70-72. doi:10.3969/j.issn.1006-6535.2007.02.017
[9] 袁士宝,蒋海岩,王丽,等. 稠油油藏蒸汽吞吐后转火烧油层适应性研究[J]. 新疆石油地质,2013,34(3):303-306. YUAN Shibao, JIANG Haiyan, WANG Li, et al. Research on adaptability to in-situ combustion in heavy oil reservoir after steam huff and puff[J]. Xinjiang Petroleum Geology, 2013, 34(3):303-306.
[10] 刘其成,刘宝良,程海清. 超稠油油藏火驱辅助重力泄油技术实验研究[J]. 特种油气藏,2015,22(1):84-87. doi:10.3969/j.issn.1006-6535.2015.01.018 LIU Qicheng, LIU Baoliang, CHENG Haiqing. Experimental study on fire-flooding assisted gravity drainage in super-heavy oil reservoirs[J]. Special Oil & Gas Reservoirs, 2015, 22(1):84-87. doi:10.3969/j.issn.1006-6535.2015.01.018
[11] 宫臣兴,李继红,史毅. 稠油开采技术及展望[J]. 辽宁化工,2018,47(4):327-329. doi:10.3969/j.issn.1004-0935.2018.04.021 GONG Chenxing, LI Jihong, SHI Yi. Heavy oil recovery technologies and their development trend[J]. Liaoning Chemical Industry, 2018, 47(4):327-329. doi:10.3969/j.issn.1004-0935.2018.04.021
[12] 束青林,王顺华,杨元亮,等. 春风油田浅薄层超稠油油藏高速高效开发关键技术[J]. 油气地质与采收率,2019,26(3):10-19. doi:10.13673/j.cnki.cn37-1359/te.2019.03.002 SHU Qinglin, WANG Shunhua, YANG Yuanliang, et al. Key technology of high-speed and high-efficiency development of thin-shallow super-heavy oil reservoir in Chunfeng Oilfield[J]. Petroleum Geology and Recovery Efficiency, 2019, 26(3):10-19. doi:10.13673/j.cnki.cn37-1359/te.2019.03.002
[13] 巴忠臣,张元,赵长虹,等. 超稠油直井水平井组合蒸汽驱参数优化[J]. 特种油气藏,2017,24(1):133-137. doi:10.3969/j.issn.1006-6535.2017.01.027 BA Zhongchen, ZHANG Yuan, ZHAO Changhong, et al. Steam flooding optimization of vertical-horizontal well combination in super-heavy oil reservoir[J]. Special Oil and Gas Reservoirs, 2017, 24(1):133-137. doi:10.3969/j.issn.1006-6535.2017.01.027
[14] 肖卫权,高孝田,张玉霞,等. 河南油田超稠油油藏蒸汽驱的可行性及先导性试验[J]. 石油天然气学报,2008,30(1):341-343. XIAO Weiquan, GAO Xiaotian, ZHANG Yuxia, et al. Feasibility and pilot test of heavy oil reservoir steam flooding in Henan Oilfield[J]. Journal of Oil and Gas Technology, 2008, 30(1):341-343.
[15] 孙新革,马鸿,赵长虹,等. 风城超稠油蒸汽吞吐后期转蒸汽驱开发方式研究[J]. 新疆石油地质,2015,36(1):61-64. doi:10.7657/XJPG20150111 SUN Xin'ge, MA Hong, ZHAO Changhong, et al. Research on ultra-heavy oil development by steam stimulation converting into steam drive combination process in Fengcheng Oilfield[J]. Xinjiang Petroleum Geology, 2015, 36(1):61-64. doi:10.7657/XJPG20150111
[16] 孙永杰. 浅层超稠油油藏蒸汽驱可行性及潜力评价[J]. 石油化工高等学校学报,2014,27(2):79-83. doi:10.3969/j.issn.1006-396X.2014.02.017 SUN Yongjie. Feasibility study and potential evaluation of steam flooding for shallow extra-heavy oil reservoir[J]. Journal of Petrochemical Universities, 2014, 27(2):79-83. doi:10.3969/j.issn.1006-396X.2014.02.017
[17] 王建勇,王学忠,杨勇,等. 春风油田薄浅层超稠油水平井蒸汽驱研究[J]. 特种油气藏,2014,21(1):95-97. doi:10.3969/j.issn.1006-6535.2014.01.023 WANG Jianyong, WANG Xuezhong, YANG Yong, et al. Steam flooding of thin shallow super heavy oil horizontal wells in Chunfeng Oilfield[J]. Special Oil and Gas Reservoirs, 2014, 21(1):95-97. doi:10.3969/j.issn.1006-6535.2014.01.023
[18] 马德胜,郭嘉,李秀峦,等. 浅薄层超稠油油藏蒸汽吞吐后开发方式实验[J]. 新疆石油地质,2013,34(4):458-461. MA Desheng, GUO Jia, LI Xiuluan, et al. Experimental study of development process of shallow and thin extra-heavy oil reservoirs following steam simulation[J]. Xinjiang Petroleum Geology, 2013, 34(4):458-461.
[19] 赵洪岩. 辽河中深层稠油蒸汽驱技术研究与应用[J]. 石油钻采工艺,2009,31(S1):110-114. doi:10.3969/j.issn.1000-7393.2009.z1.024 ZHAO Hongyan. Study and application of heavy oil steam flooding in mid-deeplayers in Liaohe Oilfield[J]. Oil Drilling & Production Technology, 2011, 31(S1):110-114. doi:10.3969/j.issn.1000-7393.2009.z1.024
[20] 柴利文. 中深层块状稠油油藏蒸汽驱主要问题及对策研究[J]. 特种油气藏,2005,12(6):44-47. doi:10.3969/j.issn.1006-6535.2005.06.014 CHAI Liwen. Main problems and countermeasures of pilot steam drive in mid-deep massive heavy oil reservoir[J]. Special Oil and Gas Reservoirs, 2005, 12(6):44-47. doi:10.3969/j.issn.1006-6535.2005.06.014
[21] 李延杰,李娜,谭先红,等. 海上M稠油油田吞吐后续转驱开发方案研究[J]. 西南石油大学学报(自然科学版),2018,40(2):98-106. doi:10.11885/j.issn.1674-5086.2016.10.27.02 LI Yanjie, LI Na, TAN Xianhong, et al. Development program of flooding after huff and puff in offshore M heavy Oilfield[J]. Journal of Southwest Petroleum University (Science & Technology Edition), 2018, 40(2):98-106. doi:10.11885/j.issn.1674-5086.2016.10.27.02
[22] 付金刚,杜殿发,郑洋,等. 超稠油油藏蒸汽驱动态预测模型[J]. 石油与天然气地质,2018,39(1):192-197. doi:10.11743/ogg20180119 FU Jingang, DU Dianfa, ZHENG Yang, et al. Dynamic prediction model of steam flooding in extra heavy oil reservoirs[J]. Oil & Gas Geology, 2018, 39(1):192-197. doi:10.11743/ogg20180119
[23] 王杰,刘德华,王梓来,等. 超薄层稠油油藏吞吐后转蒸汽驱技术研究[J]. 能源与环保,2017,39(10):69-74. doi:10.19389/j.cnki.1003-0506.2017.10.014 WANG Jie, LIU Dehua, WANG Zilai, et al. Study on steam flooding technology after huff and puff for super heavy oil reservoir[J]. China Energy and Environmental Protection, 2017, 39(10):69-74. doi:10.19389/j.cnki.10030506.2017.10.014
[24] 张方礼,刘其成,刘宝良,等. 稠油开发实验技术与应用[M]. 北京:石油工业出版社,2007:123-126. ZHANG Fangli, LIU Qicheng, LIU Baoliang, et al. Experimental technology and application of heavy oil development[M]. Beijing:Petroleum Industry Press, 2007:123-126.
[25] 国家能源局. 注蒸汽采油二维比例物理模拟实验技术要求:SY/T 7068—2016[S]. 北京:石油工业出版社,2016. National Energy Administration. The technical requirements of two-dimensional scaled physical modeling experiment for steam recovery:SY/T 7068-2016[S]. Beijing:Petroleum Industry Press, 2016.
[26] 王风岩,嵇锐,王忠伟,等. 特(超)稠油流变特性试验研究及应用[J]. 特种油气藏,2002,9(5):91-93. doi:10.3969/j.issn.1006-6535.2002.05.027 WANG Fengyan, JI Rui, WANG Zhongwei, et al. Experimental study of rheological property of extra (super) heavy oil[J]. Special Oil and Gas Reservoirs, 2002, 9(5):91-93. doi:10.3969/j.issn.1006-6535.2002.05.027
[27] 夏洪权,李辉,刘翎,等. 稠油拐点温度测算方法研究[J]. 特种油气藏,2006,13(6):49-51. doi:0.3969/j.issn.1006-6535.2006.06.015 XIA Hongquan, LI Hui, LIU Ling, et al. Study on measuring of heavy oil inflection point temperature[J]. Special Oil and Gas Reservoirs, 2006, 13(6):49-51. doi:0.3969/j.issn.1006-6535.2006.06.015
[28] 赵法军,刘永建,王广昀,等. 大庆普通稠油黏温及流变性研究[J]. 科学技术与工程,2010,10(31):7644-7647. doi:10.3969/j.issn.1671-1815.2010.31.004 ZHAO Fajun, LIU Yongjian, WANG Guangyun, et al. Study on viscosity-temperature and rheological properties of Daqing heavy oil[J]. Science Technology and Engineering, 2010, 10(31):7644-7647. doi:10.3969/j.issn.1671-1815.2010.31.004
[29] 韩继勇,侯云翌,郑维师. 冷家稠油黏温特性及流变特性实验研究[J]. 西北大学学报(自然科学版),2014,44(4):610-614. HAN Jiyong, HOU Yunyi, ZHENG Weishi. Experimental study on viscosity-temperature and rheological characteristics of Lengjia heavy oil in Liaohe Oilfield[J]. Journal of Northwest University (Natural Science Edition), 2014, 44(4):610-614.